There is no product that matches the search criteria.
Your cart is empty.
COB means chip on board. In COB LED strip lights, the closely spaced LEDs create a more continuous line of light than many conventional strips, where individual LED points can remain visible. COB LED tape is useful when the light source can be seen directly, such as beneath cabinets, along shelves or inside a display. The finished appearance still depends on the strip, viewing distance, surface and any profile or diffuser used; check whether your installation needs additional diffusion.
Our current COB LED strip range uses 24V and includes single-colour warm white and natural white options, plus RGB. The products are listed as IP20 for dry indoor use. COB describes the LED layout; it does not by itself confirm the colour, brightness, voltage, dimming compatibility or environmental rating. Check the individual product specification before choosing.
Cut spacing and output vary by model. Use each product page as the source of truth for the strip you select, and do not transfer one model's cut interval or colour details to another.
Match the LED driver output voltage to the strip: these products require 24V operation. To estimate the strip's nominal load, multiply its wattage per metre by the run length. A 5m roll at 12W/m is 60W; at 14.4W/m it is 72W; and at 16W/m it is 80W. Select a compatible constant-voltage 24V driver with capacity for the full load and any margin required by the manufacturer. Check the maximum run length and connection guidance for the chosen product. Never connect low-voltage LED tape directly to mains power or to a 12V supply.
Measure the run and position the strip before cutting. Cut only at the marked points for the exact model, and switch off and isolate the power first. The three listings have different cut intervals, so a 55mm mark on one strip does not apply to the others. Check the connector width and contact layout against the product, or use the connection leads supplied with the selected roll. Keep polarity and controller connections consistent with the manufacturer's instructions.
All three listed strips are 10mm wide. If you are using an aluminium LED profile, check its internal width and diffuser clearance as well as the strip width. A profile can provide a straight mounting surface and help manage heat; follow the strip and profile instructions for ventilation and installation.
For warm white, compare the 2700K options; the 12W/m model also offers a 4200K natural-white selection. Where colour appearance matters, the 14.4W/m product is specified with Ra above 90. RGB tape changes colour through compatible controls and is not the same as a single-colour white strip. Choose a controller that matches the RGB channels, 24V supply and total electrical load.
Dimming is a system choice. Confirm that the strip, driver and dimmer or controller are all designed to work together. Some installations use a low-voltage controller between the 24V driver and tape; mains-side dimming requires a driver specifically rated for the chosen dimming method. Do not assume a standard wall dimmer will work with a non-dimmable driver. Browse our LED strip controllers and dimmable LED drivers and check their specifications against the selected tape.
IP20 is intended for dry indoor locations and does not protect the strip from water. These products should not be selected for exposed outdoor or wet-area use. For any moisture-prone location, check the rating of the complete installation, including the strip, connectors, driver and enclosure. Use a qualified electrician for mains wiring or changes to the electrical installation.
Choose a COB light strip when you want a more continuous appearance and the tape will be close to view. Compare brightness in lumens, power in watts per metre, colour temperature, colour-rendering data, IP rating and cut points before selecting. For a standard LED strip with visible individual diodes or a different voltage, browse our wider LED strip lights and LED tape range. For profiles and diffusers, see our LED strip channels. For practical help matching a driver or controller, contact our team before ordering.
COB means chip on board. It describes an LED arrangement with closely spaced light sources on the strip, designed to give a more continuous appearance than many conventional LED strips. Check the product details for the actual LED count, output and colour options.
These products can be cut at their designated marks, but the spacing differs by model: 55mm, 42mm or 33mm in the current listings. Follow the specific product instructions and do not cut elsewhere.
Do not assume that every COB strip is dimmable. Confirm the strip's specification and use a compatible dimmer or controller and 24V driver. For RGB tape, use a controller designed for RGB output and rated for the full load.
The listed strips are IP20 for dry indoor use. Choose a product and complete electrical system with an appropriate environmental rating for any outdoor or moisture-prone installation.